Re: gEDA-user: PCB+GL Testers (please test)

["Bert Timmerman" <bert.timmerman@xxxxxxxxx>]

Hi Peter, 

> -----Original Message-----
> From: geda-user-bounces@xxxxxxxxxxxxxx 
> [mailto:geda-user-bounces@xxxxxxxxxxxxxx] On Behalf Of Bert Timmerman
> Sent: Saturday, November 06, 2010 2:35 PM
> To: 'gEDA user mailing list'
> Subject: Re: gEDA-user: PCB+GL Testers (please test)
> 
> Hi Peter, 
> 
> > -----Original Message-----
> > From: geda-user-bounces@xxxxxxxxxxxxxx 
> > [mailto:geda-user-bounces@xxxxxxxxxxxxxx] On Behalf Of Peter Clifton
> > Sent: Thursday, November 04, 2010 1:51 AM
> > To: gEDA user mailing list
> > Subject: Re: gEDA-user: PCB+GL Testers (please test)
> > 
> > On Wed, 2010-11-03 at 22:04 +0100, Kai-Martin Knaak wrote:
> > > Peter Clifton wrote:
> > > 
> > > > I've got a load of changes I've been working on recently
> > in PCB+GL,
> > > > this time on my "local_customisation_no_pours" branch.
> > > 
> > > For those not familiar with git, these are the commands I ran to 
> > > install Peters version in /usr/local/bin/pcb-test :
> > > 
> > > /------------------------
> > > git clone git://repo.or.cz/geda-pcb/pcjc2.git
> > > cd pcjc2
> > > git checkout -b local_customisation_no_pours
> > 
> > Did this work and give you the 3D / GL stuff? (Does git 
> automatically 
> > pick the right remote branch?)
> > 
> > I would have done:
> > 
> > git checkout -b local_customisation_no_pours 
> > origin/local_customisation_no_pours
> > 
> > But since I learnt to do that some while back, things might 
> have got 
> > easier since.
> > 
> > --
> > Peter Clifton
> > 
> > Electrical Engineering Division,
> > Engineering Department,
> > University of Cambridge,
> > 9, JJ Thomson Avenue,
> > Cambridge
> > CB3 0FA
> > 
> > Tel: +44 (0)7729 980173 - (No signal in the lab!)
> > Tel: +44 (0)1223 748328 - (Shared lab phone, ask for me)
> > 
> > 
> > 
> 
> I tried the above and ran into trouble with the requirement 
> of gtkglext-1.0:
> there seems to be no such RPM package available for Fedora 13 ;-(
> 
> So I will try to find (or build) and install a package this weekend.
> 
> To be continued ...
> 
> Kind regards,
> 
> Bert Timmerman
> 
> 

The LED2.pcb example gives:

1.2 ... 1.3 redraws per second on your local_customisation_no_pours branch.

15.8 redraws per second on your before_pours branch.

81.8 redraws per second on the pcb-20091103 (yum installed) out of the box
RPM version .

59.8 redraws per second on pcb.gpleda.org/pcb.git HEAD (just sync'ed).

66.6 redraws per second on pcb-20100929 tarball.

Hardware is a Packard Bell Notebook (MH35U070) 1.8GB with 1.89 MHz DualCore
T2390 and  SIS Mirage 3+ graphics (256 MB).

Hope this helps a bit.

Kind regards,

Bert Timmerman.



_______________________________________________
geda-user mailing list
geda-user@xxxxxxxxxxxxxx
http://www.seul.org/cgi-bin/mailman/listinfo/geda-user