I did a lot of tuning on the Raspberry Pi and it's now much, much more
stable as a Tor relay, but just now I had another "circuit creation
storm." ÂInterestingly, the Pi remained up, and my *router* crashed.
I've also seen huge bursts of circuit creation on a relay I run on a
VPS, but as it's a much more powerful box it rarely complains (and thus
I rarely notice).
This many circuits and outbound connections is highly unusual for the
small relay I'm running on the Pi. ÂAnd this behavior definitely occurs
in bursts. ÂIs this an outbound DDOS or an attack on Tor itself? ÂIf the
former (or maybe the latter), is there some way I could perhaps use
iptables to temporarily "clamp" the ability to open TCP connections when
Tor (or anything on the Pi) opens a number over some threshold in some
short period of time?
Here's log output (via 'arm') from the relay after my router crashed
twice, I went to the admin panel and noted hundreds of outbound
connections from my Tor box. ÂTime is America/Los_Angeles.
â 13:55:00 [ARM_NOTICE] Relay unresponsive (last heartbeat: Sat May Â4 13:54:14 2013)
Ââ 13:52:25 [WARN] Your computer is too slow to handle this many circuit
ÂcreationÂâ Â a more restricted exit policy. [404 similar message(s) suppressed
Ââ Â requests! Please consider using the MaxAdvertisedBandwidth config
Âoption or choosing
Âin last 60 seconds]
Ââ 13:51:07 [WARN] Your computer is too slow to handle this many circuit
ÂcreationÂâ Â a more restricted exit policy. [75 similar message(s) suppressed in
Ââ Â requests! Please consider using the MaxAdvertisedBandwidth config
Âoption or choosing
Âlast 60 seconds]
Ââ 13:50:52 [WARN] Your computer is too slow to handle this many circuit
ÂcreationÂâ Â a more restricted exit policy. [601 similar message(s) suppressed
Ââ Â requests! Please consider using the MaxAdvertisedBandwidth config
Âoption or choosing
Âin last 60 seconds]
Ââ 13:48:39 [WARN] Your computer is too slow to handle this many circuit
ÂcreationÂâ Â a more restricted exit policy. [99 similar message(s) suppressed in
Ââ Â requests! Please consider using the MaxAdvertisedBandwidth config
Âoption or choosing
Âlast 60 seconds]
Ââ 13:47:34 [WARN] Your computer is too slow to handle this many circuit
ÂcreationÂâ Â a more restricted exit policy. [22 similar message(s) suppressed in
Ââ Â requests! Please consider using the MaxAdvertisedBandwidth config
Âoption or choosing
Âlast 60 seconds]
Ââ 13:46:17 [WARN] Your computer is too slow to handle this many circuit
ÂcreationÂâ Â a more restricted exit policy. [253 similar message(s) suppressed
Ââ Â requests! Please consider using the MaxAdvertisedBandwidth config
Âoption or choosing
Âin last 60 seconds]
Ââ 13:43:47 [WARN] Your computer is too slow to handle this many circuit
ÂcreationÂâ Â a more restricted exit policy. [1396 similar message(s) suppressed
Ââ Â requests! Please consider using the MaxAdvertisedBandwidth config
Âoption or choosing
Âin last 60
Ââ Â seconds]
Ââ 13:42:48 [WARN] Your computer is too slow to handle this many circuit
ÂcreationÂâ Â a more restricted exit policy. [16 similar message(s) suppressed in
Ââ Â requests! Please consider using the MaxAdvertisedBandwidth config
Âoption or choosing
Âlast 60 seconds]
Here's how it crashed my router (blowing ip_conntrack limits is
sufficient only to mess up many of my TCP connections, but eventually
the router runs out of memory and starts killing processes):
May Â4 13:51:24 dedmaus user.warn kernel: ip_conntrack: table full,
dropping packet.
May Â4 13:51:24 dedmaus user.warn kernel: ip_conntrack: table full,
dropping packet.
May Â4 13:51:24 dedmaus user.warn kernel: ip_conntrack: table full,
dropping packet.
May Â4 13:51:25 dedmaus user.warn kernel: ip_conntrack: table full,
dropping packet.
May Â4 13:51:29 dedmaus user.warn kernel: NET: 152 messages suppressed.
May Â4 13:51:29 dedmaus user.warn kernel: ip_conntrack: table full,
dropping packet.
May Â4 13:51:34 dedmaus user.warn kernel: NET: 193 messages suppressed.
May Â4 13:51:34 dedmaus user.warn kernel: ip_conntrack: table full,
dropping packet.
May Â4 13:51:39 dedmaus user.warn kernel: NET: 227 messages suppressed.
...ad infinitum with the number of messages suppressed per 5 sec
increasing until the router crashes.
On Mon, Mar 18, 2013, at 06:18 PM, torsion@xxxxxxxx wrote:
> I'm also seeing occasional messages like this on the Pi (it never lasts
> long):
>
> 18:13:24 [ARM_NOTICE] Relay resumed
> 18:13:18 [ARM_NOTICE] Relay unresponsive (last heartbeat: Mon Mar 18
> 18:13:04 2013)
> 17:28:43 [ARM_NOTICE] Relay resumed
> 17:28:38 [ARM_NOTICE] Relay unresponsive (last heartbeat: Mon Mar 18
> 17:28:25 2013)
> 14:12:26 [ARM_NOTICE] Relay resumed
> 14:12:20 [ARM_WARN] Deduplication took too long. Its current
> implementation has difficulty handling large logs so disabling it to
> keep the interface responsive.
> 14:12:20 [ARM_NOTICE] Relay unresponsive (last heartbeat: Mon Mar 18
> 14:12:06 20
>
> On Mon, Mar 18, 2013, at 01:00 PM, torsion@xxxxxxxx wrote:
> > Hi there, I just joined the mailing list and apologized if this has been
> > discussed before. ÂI did find discussion of a similar issue in January
> > 2013's archive:
> >
> > https://lists.torproject.org/pipermail/tor-relays/2013-January/001809.html
> >
> > It's important to note that I believe I've seen (but didn't save logs) a
> > couple "circuit creation burst" events on my established relay (about
> > 5Mbps, stable, guard, non-exit) which was mostly able to handle it
> > without crashing as it has plenty of RAM and the above-mentioned
> > messages - "Your computer is too slow to handle this many circuit
> > creation requests! Please consider using the MaxAdvertisedBandwidth
> > config option or choosing a m ore restricted exit policy." - appear only
> > with the relay is under load for other reasons AND a large number of
> > circuits are being suddenly created.
> >
> > I wondered if this was some kind of DOS attempt but didn't think much of
> > it because my fast relay continued working fine.
> >
> > However, I've just set up a Raspberry Pi, the 512MB model, as a relay on
> > a slower connection. ÂHere are the relevant settings on this relay:
> >
> > RelayBandwidthRate 130 KB
> > RelayBandwidthBurst 340 KB
> >
> > The Pi has a fairly slow CPU, so I'd occasionally get messages about log
> > deduplication being too slow or something, but didn't think much of it.
> > I finally got the relay up and left it up for over 24 hours. ÂWhen I
> > woke up this morning it had crashed. ÂHere are the relevant log messages
> > - note the huge jump in number of circuits between 22:35 and 04:35
> > (maybe I got the Stable flag), then the storm of circuit open requests
> > starting at 05:49. ÂEventually I believe the Pi ran out of memory and
> > killed the tor process.
> >
> > What's very interesting here is that my fast VPS relay with a
> > RelayBandwidthRate over 5x faster is almost never handling much more
> > than 1000 circuits, so why all of a sudden the demand on the Pi that's
> > advertising a lower bandwidth rate?
> >
> > Mar 17 22:35:00.000 [notice] Heartbeat: Tor's uptime is 1 day 0:00
> > hours, with 26 circuits open. I've sent 974.13 MB and received 969.92
> > MB.
> > Mar 18 04:35:00.000 [notice] Heartbeat: Tor's uptime is 1 day 6:00
> > hours, with 972 circuits open. I've sent 1.61 GB and received 1.59 GB.
> > Mar 18 05:49:44.000 [warn] Your computer is too slow to handle this many
> > circuit creation requests! Please consider using the
> > MaxAdvertisedBandwidth config option or choosing a more restricted exit
> > policy.
> > Mar 18 05:49:44.000 [warn] Failed to hand off onionskin. Closing.
> > Mar 18 05:50:44.000 [warn] Your computer is too slow to handle this many
> > circuit creation requests! Please consider using the
> > MaxAdvertisedBandwidth config option or choosing a more restricted exit
> > policy. [5817 similar message(s) suppressed in last 60 seconds]
> > Mar 18 05:52:30.000 [warn] Your system clock just jumped 101 seconds
> > forward; assuming established circuits no longer work.
> > Mar 18 05:53:51.000 [warn] Your computer is too slow to handle this many
> > circuit creation requests! Please consider using the
> > MaxAdvertisedBandwidth config option or choosing a more restricted exit
> > policy. [1055 similar message(s) suppressed in last 60 seconds]
> > Mar 18 05:55:14.000 [warn] Your computer is too slow to handle this many
> > circuit creation requests! Please consider using the
> > MaxAdvertisedBandwidth config option or choosing a more restricted exit
> > policy. [329 similar message(s) suppressed in last 60 seconds]
> >
> > I'd like to figure out just how much the Raspberry Pi is capable of,
> > because it could be a cheap way to build out the relay network by people
> > who want to donate bandwidth - but of course it needs to be stable, and
> > something about my setup is not.
> >
> > Also:
> >
> > Mar 16 20:55:33.000 [notice] No AES engine found; using AES_* functions.
> >
> > I have no idea if the Broadcom BCM2835 SoC (ARM1176JZF-S CPU) in the Pi
> > has any AES capability, but it'd be great to find out.
> >
> > _______________________________________________
> > tor-relays mailing list
> > tor-relays@xxxxxxxxxxxxxxxxxxxx
> > https://lists.torproject.org/cgi-bin/mailman/listinfo/tor-relays
_______________________________________________
tor-relays mailing list
tor-relays@xxxxxxxxxxxxxxxxxxxx
https://lists.torproject.org/cgi-bin/mailman/listinfo/tor-relays
_______________________________________________ tor-relays mailing list tor-relays@xxxxxxxxxxxxxxxxxxxx https://lists.torproject.org/cgi-bin/mailman/listinfo/tor-relays