Re: [tor-relays] Relay's clock settings off no matter what

[eric gisse <jowr.pi@xxxxxxxxx>]

If your vps provider is openvz, you are shit out of luck because you
can't set time.

On Fri, Nov 14, 2014 at 4:37 AM, s7r <s7r@xxxxxxxxxx> wrote:
> -----BEGIN PGP SIGNED MESSAGE-----
> Hash: SHA1
>
> Hello Austin,
>
> The clock is very important to Tor, you need accurate clock all the time.
>
> Do you run NTPDATE or NTPD service inside your VPS? The virutal
> servers are sometimes problematic, depending on virtualization, when
> coming to hwclock and dedicated time.
>
> You need to open a ticket with your VPS provider and ask them what
> virtualization technique they use and if there is a NTP daemon on the
> hypervisor (physical host server) which sets the time inside the
> guests (virtual machines). Make sure the time is correct on your
> master host server and rely on that time instead of trying to run your
> own NTP service. If they say the master server doesn't run this
> service or set the time inside guests (i doubt it), you can then run
> NTP inside your VPS as follows:
>
> (NTP and NTPDATE are included in FreeBSD base system so you don't have
> to install anything). Run these commands:
>
> $ service ntpd stop
> (or onestop if stop doesn't work, if it says ntpd is not running just
> proceed with the following commands)
>
> $ echo 'ntp_enable="YES"' >> /etc/rc.conf
> $ echo 'ntpdate_enable="YES"' >> /etc/rc.conf
> $ ntpdate 0.rhel.pool.ntp.org
> $ service ntpd start
>
> Your timezone does not matter. Tor calculates the time in UNIX time
> format, so you can be in any time zone, GMT +1, UTC, EET, whatever -
> Tor will work just fine if the UNIX time format is accurate. The
> localtime via timezone is just a translation/calculation of UNIX
> timestamp.
>
> On 11/14/2014 6:59 AM, Austin Bentley wrote:
>> Hello everyone,
>>
>> I have an interesting problem. I am monitoring my relay using arm.
>> I am getting the following warnings:
>>
>>> 05:56:12 [WARN] Received directory with skewed time (server
>> '154.35.32.5:80'): It seems that our clock is behind by 1 hours, 0
>> minutes, or that theirs is ahead. Tor requires an accurate clock
>> to work: please check your time, timezone, and date settings.
>>
>> Most of the messages tell me that my clock is an hour behind.
>> However, I also get these messages occasionally (but not as
>> often):
>>> 02:07:27 [WARN] Our clock is 52 minutes, 35 seconds behind the
>>> time
>> published in the consensus network status document (2014-11-14
>> 02:00:00 UTC).  Tor needs an accurate clock to work correctly.
>> Please check your time and date settings!
>>
>>
>> I am running a Tor exit relay on a FreeBSD VPS. Said VPS is in
>> Czech Republic. If I set the time to CET, it is 1 hour behind true
>> CET (GMT+1); therefore, I have it set to EET (GMT+2.)  I have
>> verified the time is correct in Czech Republic. This problem is
>> rather frustrating because it is causing my server to throw away
>> circuit data as old data.
>>
>> Could someone shine some light on this?
>>
>> Thanks, Austin
>>
>>
>> _______________________________________________ tor-relays mailing
>> list tor-relays@xxxxxxxxxxxxxxxxxxxx
>> https://lists.torproject.org/cgi-bin/mailman/listinfo/tor-relays
>>
> -----BEGIN PGP SIGNATURE-----
> Version: GnuPG v2.0.22 (MingW32)
>
> iQEcBAEBAgAGBQJUZdtcAAoJEIN/pSyBJlsRMzMH/3F1MeX9Z1y7z4G+zNNDENin
> Yytg5YsXrWrwFCiC90j6rmKIY2rFvu5YTqpnoZ28bmC8+ZePuCXM1srK62YnUlvP
> YVYJO1bCP0gl7ER1MhffS5pcpvXZ4Mb+uPdk1MlKcO+yD7xgP0EwbojBRJp/23Ct
> jjkeLIg9fkDb+TRVd3KKFfvgHaItGYAoMc3Jn9yVUrH1vmKUDWe4XeSt37ejx4iE
> 6431+KUeFkEzPMJII2hBDJ3HFGx+VFAfBa+V2jQ+5DzIUwTc710jgmjSy7xhv/4Z
> +V7JDniU6bDt0U1SIpKfZBGThrIiT7vsBg9EWQcQf1IHTvXe5boDkoveUdyIytk=
> =Kczu
> -----END PGP SIGNATURE-----
> _______________________________________________
> tor-relays mailing list
> tor-relays@xxxxxxxxxxxxxxxxxxxx
> https://lists.torproject.org/cgi-bin/mailman/listinfo/tor-relays
_______________________________________________
tor-relays mailing list
tor-relays@xxxxxxxxxxxxxxxxxxxx
https://lists.torproject.org/cgi-bin/mailman/listinfo/tor-relays