[Author Prev][Author Next][Thread Prev][Thread Next][Author Index][Thread Index]

Re: gEDA-user: PCB from cvs

George --

When you pull stuff out of CVS you usually need to use the automake
tools before doing configure.  The easiest way to do that is to run
autogen.sh (assuming it exists) like this:

rm -rf pcb
cvs -d:pserver:anonymous@xxxxxxxxxxxxxxxxxxxxxxx:/cvsroot/pcb login
cvs -d:pserver:anonymous@xxxxxxxxxxxxxxxxxxxxxxx:/cvsroot/pcb co pcb
cd pcb
sh autogen.sh
./configure
make


Stuart



On Mon, 31 Jul 2006, George M. Gallant, Jr. wrote:

DJ,

The only log file is config.log.

Restarted from scratch:

   rm -rf pcb
   cvs -d:pserver:anonymous@xxxxxxxxxxxxxxxxxxxxxxx:/cvsroot/pcb login
   cvs -d:pserver:anonymous@xxxxxxxxxxxxxxxxxxxxxxx:/cvsroot/pcb co pcb
   cd pcb
   ./configure
   make

The following is the last few lines of the make output

George

Making all in doc
make[2]: Entering directory `/home3/local/src/geda/pcb/doc'
make  all-am
make[3]: Entering directory `/home3/local/src/geda/pcb/doc'
rm -rf pcb.htp
if /bin/sh /usr/local/src/geda/pcb/missing --run makeinfo --html
--css-include=./pcb.css --no-split  -I . \
-o pcb.htp pcb.texi; \
then \
 rm -rf pcb.html; \
 if test ! -d pcb.htp && test -d pcb; then \
   mv pcb pcb.html; else mv pcb.htp pcb.html; fi; \
else \
 if test ! -d pcb.htp && test -d pcb; then \
   rm -rf pcb; else rm -Rf pcb.htp pcb.html; fi; \
 exit 1; \
fi
/home3/local/src/geda/pcb/doc//actions.texi:1335: @image file
`puller.png' (for HTML) not readable: No such file or directory.
pcb.texi:5805: @image file `thermal.png' (for HTML) not readable: No
such file or directory.
makeinfo: Removing output file `pcb.htp' due to errors; use --force to
preserve.
make[3]: *** [pcb.html] Error 1
make[3]: Leaving directory `/home3/local/src/geda/pcb/doc'
make[2]: *** [all] Error 2
make[2]: Leaving directory `/home3/local/src/geda/pcb/doc'
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory `/home3/local/src/geda/pcb'
make: *** [all] Error 2

On Mon, 2006-07-31 at 10:19 -0400, DJ Delorie wrote:

Executing make from the top level fails without these files. I
copied them from 20060422 to get past the problem. Either they are
needed or the make file needs reflect the current condition.


That's odd.  The Makefile has an unconditional rule to build them:

.pcb.png :
	../src/pcb-bin -x png --only-visible --font-path $(top_srcdir)/src --outfile $@ $<

Could you post a log of your build session?  There must be an error
message in there somewhere.


_______________________________________________
geda-user mailing list
geda-user@xxxxxxxxxxxxxx
http://www.seul.org/cgi-bin/mailman/listinfo/geda-user




_______________________________________________
geda-user mailing list
geda-user@xxxxxxxxxxxxxx
http://www.seul.org/cgi-bin/mailman/listinfo/geda-user