[Author Prev][Author Next][Thread Prev][Thread Next][Author Index][Thread Index]
RE: gEDA-user: PCB footprint - 2 sided part
Thank you again. I am starting to catch on to this program... I still have a
lot to learn.
-Joel
> -----Original Message-----
> From: geda-user-bounces@xxxxxxxxxxxxxx [mailto:geda-user-
> bounces@xxxxxxxxxxxxxx] On Behalf Of John Luciani
> Sent: Wednesday, December 27, 2006 6:53 PM
> To: gEDA user mailing list
> Subject: Re: gEDA-user: PCB footprint - 2 sided part
>
> On 12/27/06, Ostheller, Joel A. <JOEL.A.OSTHELLER@xxxxxxxx> wrote:
> >
> >
> > Can I get some tips on how I would create a footprint for this SMA right
> > angle connector that lives on both sides of the board? Should I create
> it
> > with through holes? Should I create two footprints and just make sure to
> > line them up? Perhaps I should have picked an easier part to do my first
> > footprint? Very not obvious.
> >
> >
> http://emersonnetworkpower.com/webapp/wcs/stores/servlet/ESC/resources/142
> 07
> > 11821.pdf
> >
>
> Below are footprints for the 142-0711-821 and 142-0701-801.
>
> NB: Carefully check these footprints against the specification.
>
> (* jcl *)
> --
> http://www.luciani.org
>
>
> # 142-0701-801
>
> Element[0x0 "SMA" "" "" 0 0 23500 -5000 0 100 0x0]
> (
> Pad[0 -5500 0 5500 9000 2000 11000 "" "1" 0x0100]
> Pad[0 -5500 0 5500 9000 2000 11000 "" "1" 0x0180]
> Pad[-17000 -5250 -17000 5250 9500 2000 11500 "" "2" 0x0100]
> Pad[-17000 -5250 -17000 5250 9500 2000 11500 "" "2" 0x0180]
> Pad[-17000 10750 -17000 12550 1800 2000 3800 "" "2" 0x0100]
> Pin[-17000 13650 3800 2000 5800 1800 "" "2" 0x01]
> Pad[-17000 10750 -17000 12550 1800 2000 3800 "" "2" 0x0180]
> Pin[-17000 13650 3800 2000 5800 1800 "" "2" 0x01]
> Pad[17000 -5250 17000 5250 9500 2000 11500 "" "2" 0x0100]
> Pad[17000 -5250 17000 5250 9500 2000 11500 "" "2" 0x0180]
> Pad[17000 10750 17000 12550 1800 2000 3800 "" "2" 0x0100]
> Pin[17000 13650 3800 2000 5800 1800 "" "2" 0x01]
> Pad[17000 10750 17000 12550 1800 2000 3800 "" "2" 0x0180]
> Pin[17000 13650 3800 2000 5800 1800 "" "2" 0x01]
> ElementLine[-16000 -13750 16000 -13750 5500]
> ElementLine[-13000 -13750 -13000 -26000 1000]
> ElementLine[-13000 -26000 -16000 -26000 1000]
> ElementLine[-16000 -26000 -16000 -47000 1000]
> ElementLine[-16000 -47000 16000 -47000 1000]
> ElementLine[16000 -47000 16000 -26000 1000]
> ElementLine[16000 -26000 13000 -26000 1000]
> ElementLine[13000 -26000 13000 -13750 1000]
> )
>
>
>
> # 142-0711-821
> Element[0x0 "SMA" "" "" 0 0 20500 -5000 0 100 0x0]
> (
> Pad[0 -4750 0 4750 7000 2000 9000 "" "1" 0x0100]
> Pad[0 -4750 0 4750 7000 2000 9000 "" "1" 0x0180]
> Pad[-12000 -3000 -12000 3000 10500 2000 12500 "" "2" 0x0100]
> Pad[-12000 -3000 -12000 3000 10500 2000 12500 "" "2" 0x0180]
> Pad[-12000 9000 -12000 10800 1800 2000 3800 "" "2" 0x0100]
> Pin[-12000 11900 3800 2000 5800 1800 "" "2" 0x01]
> Pad[-12000 9000 -12000 10800 1800 2000 3800 "" "2" 0x0180]
> Pin[-12000 11900 3800 2000 5800 1800 "" "2" 0x01]
> Pad[12000 -3000 12000 3000 10500 2000 12500 "" "2" 0x0100]
> Pad[12000 -3000 12000 3000 10500 2000 12500 "" "2" 0x0180]
> Pad[12000 9000 12000 10800 1800 2000 3800 "" "2" 0x0100]
> Pin[12000 11900 3800 2000 5800 1800 "" "2" 0x01]
> Pad[12000 9000 12000 10800 1800 2000 3800 "" "2" 0x0180]
> Pin[12000 11900 3800 2000 5800 1800 "" "2" 0x01]
> ElementLine[-9750 -12000 9750 -12000 5500]
> ElementLine[-6750 -12000 -6750 -24250 1000]
> ElementLine[-6750 -24250 -9750 -24250 1000]
> ElementLine[-9750 -24250 -9750 -45250 1000]
> ElementLine[-9750 -45250 9750 -45250 1000]
> ElementLine[9750 -45250 9750 -24250 1000]
> ElementLine[9750 -24250 6750 -24250 1000]
> ElementLine[6750 -24250 6750 -12000 1000]
> )
>
>
> _______________________________________________
> geda-user mailing list
> geda-user@xxxxxxxxxxxxxx
> http://www.seul.org/cgi-bin/mailman/listinfo/geda-user
_______________________________________________
geda-user mailing list
geda-user@xxxxxxxxxxxxxx
http://www.seul.org/cgi-bin/mailman/listinfo/geda-user