gEDA-user: pcb doesn't find my pins

[Jim <jim@xxxxxxxxx>]

When I do an optimize rats nest I don't see anything but I do get a 
bunch of errors in the log like this:

Can't find U102 pin J1-13 called for in netlist.
Can't find U102 pin J1-8 called for in netlist.
Can't find U102 pin J1-9 called for in netlist.
Can't find U102 pin J1-10 called for in netlist.
Can't find U102 pin J2-3 called for in netlist.
Can't find U102 pin J1-18 called for in netlist.
Can't find U102 pin J1-11 called for in netlist.
Can't find U102 pin J2-1 called for in netlist.
Can't find U102 pin J1-12 called for in netlist.
Nothing more to add, but there are
either rat-lines in the layout, disabled nets
in the net-list, or missing components

Did the following do something nasty to me?  Also found in the log 
previous to the above errors.

board.cmd : line 46  : "ChangePinName(U102, J1-1, MOSI)"
board.cmd : line 47  : "ChangePinName(U102, J1-2, MISO)"
board.cmd : line 48  : "ChangePinName(U102, J1-11, GND)"
board.cmd : line 49  : "ChangePinName(U102, J1-3, D7)"
board.cmd : line 50  : "ChangePinName(U102, J1-4, D6)"
board.cmd : line 51  : "ChangePinName(U102, J1-5, D5)"
board.cmd : line 52  : "ChangePinName(U102, J1-6, D4)"
board.cmd : line 53  : "ChangePinName(U102, J1-7, D3)"
board.cmd : line 54  : "ChangePinName(U102, J1-8, D2)"
board.cmd : line 55  : "ChangePinName(U102, J1-9, D1)"
board.cmd : line 56  : "ChangePinName(U102, J1-10, D0)"
board.cmd : line 57  : "ChangePinName(U102, J1-13, A14)"
... there are 25 or so changing the names of all the pins in both U102 
and U101.

Extract from the symbol for U102:

v 20100302 1 1
P 2100 8500 1900 8500 1 0 0
{
T 1900 8550 5 8 1 1 0 0 1
pinnumber=J2-1
T 1900 8450 5 8 0 1 0 2 1
pinseq=2
T 1750 8500 9 8 1 1 0 6 1
pinlabel=3V3D
T 1750 8500 5 8 0 1 0 8 1
pintype=in
}
V 1850 8500 50 6 0 0 0 -1 -1 0 -1 -1 -1 -1 -1
P 2100 8100 1900 8100 1 0 0
{
T 1900 8150 5 8 1 1 0 0 1
pinnumber=J2-18
T 1900 8050 5 8 0 1 0 2 1
pinseq=23
T 1750 8100 9 8 1 1 0 6 1
pinlabel=A0
T 1750 8100 5 8 0 1 0 8 1
pintype=in
}

and
   Pin(310 -450 60 28 "J1-1" 0x101)
   Pin(310 350 60 28 "J2-1" 0x101)
   Pin(310 -350 60 28 "J1-2" 0x01)
   Pin(310 450 60 28 "J2-2" 0x01)
   Pin(210 -450 60 28 "J1-3" 0x01)
   Pin(210 350 60 28 "J2-3" 0x01)
   Pin(210 -350 60 28 "J1-4" 0x01)
   Pin(210 450 60 28 "J2-4" 0x01)
   Pin(110 -450 60 28 "J1-5" 0x01)
   Pin(110 350 60 28 "J2-5" 0x01)
   Pin(110 -350 60 28 "J1-6" 0x01)

Just to show that I think the pin names match between the footprint and 
the symbol.

I'm very confused.

I have just two parts in this.  I generated two symbols and one 
footprint.  I used a "DIL 40 600" footprint for the one part.  I ran 
just a few nets to see if I had everything set up OK.  Obviously not.

Thanks,
Jim.





_______________________________________________
geda-user mailing list
geda-user@xxxxxxxxxxxxxx
http://www.seul.org/cgi-bin/mailman/listinfo/geda-user