gEDA-user: gEDA 1.2.0, opamp-1.sym pin numbers?

[Stefan Salewski <mail@xxxxxxxxxxxx>]

Hello,

I am a little bit confused by opamp-1.sym and opamp-2.sym of geda-1.2.0.

These symbols use pinnumbers 1 to 5.

I think this can not be compatible with ordinary DIP8 footprints.
Is there a special footprint for these opamp symbols?

stefan@AMD64X2 ~/gEDA/DAQ-Board $
cat /usr/share/gEDA/sym/analog/opamp-1.sym
v 20050820 1
L 200 800 200 0 3 0 0 0 -1 -1
L 200 800 800 400 3 0 0 0 -1 -1
T 700 800 5 10 0 0 0 0 1
device=OPAMP
L 800 400 200 0 3 0 0 0 -1 -1
L 300 650 300 550 3 0 0 0 -1 -1
L 250 600 350 600 3 0 0 0 -1 -1
L 250 200 350 200 3 0 0 0 -1 -1
P 0 600 200 600 1 0 0
{
T 150 650 5 8 1 1 0 6 1
pinnumber=1
T 150 550 5 8 0 1 0 8 1
pinseq=1
T 250 600 9 8 0 1 0 0 1
pinlabel=in+
T 250 600 5 8 0 1 0 2 1
pintype=in
}
P 0 200 200 200 1 0 0
{
T 150 250 5 8 1 1 0 6 1
pinnumber=2
T 150 150 5 8 0 1 0 8 1
pinseq=2
T 250 200 9 8 0 1 0 0 1
pinlabel=in-
T 250 200 5 8 0 1 0 2 1
pintype=in
}
P 800 400 1000 400 1 0 1
{
T 800 450 5 8 1 1 0 0 1
pinnumber=5
T 800 350 5 8 0 1 0 2 1
pinseq=5
T 750 400 9 8 0 1 0 6 1
pinlabel=out
T 750 400 5 8 0 1 0 8 1
pintype=out
}
P 500 600 500 800 1 0 1
{
T 550 600 5 8 1 1 0 0 1
pinnumber=3
T 550 600 5 8 0 1 0 2 1
pinseq=3
T 500 600 9 8 0 1 0 5 1
pinlabel=V+
T 500 550 5 8 0 1 0 5 1
pintype=pwr
}
P 500 200 500 0 1 0 1
{
T 550 100 5 8 1 1 0 0 1
pinnumber=4
T 550 100 5 8 0 1 0 2 1
pinseq=4
T 500 200 9 8 0 1 0 3 1
pinlabel=V-
T 500 300 5 8 0 1 0 3 1
pintype=pwr
}
T 700 600 8 10 1 1 0 0 1
refdes=U?
T 700 1200 5 10 0 0 0 0 1
description=operational amplifier
T 700 1000 5 10 0 0 0 0 1
numslots=0
T 700 1400 5 10 0 0 0 0 1
symversion=0.1
stefan@AMD64X2 ~/gEDA/DAQ-Board $ 





_______________________________________________
geda-user mailing list
geda-user@xxxxxxxxxxxxxx
http://www.seul.org/cgi-bin/mailman/listinfo/geda-user